Customer Support
+34 972 661 661
Price (inc. VAT)
€125.00
€195.00
Offer
-36%
Price (inc. VAT)
€49.00
€65.00
Offer
-25%
Price (inc. VAT)
€59.00
€101.00
Offer
-42%
Price (inc. VAT)
€25.00
€57.00
Offer
-56%
Price (inc. VAT)
€89.00
€249.00
Offer
-64%
Price (inc. VAT)
€69.95
€75.00
Offer
-7%
Price (inc. VAT)
€3,925.00
€5,375.00
Offer
-27%
Price (inc. VAT)
€368.00
€498.00
Offer
-26%
Price (inc. VAT)
€29.95
€62.00
Offer
-52%
Price (inc. VAT)
€149.00
€199.00
Offer
-25%

Ikelite 4405

Manufacturer: Ikelite
Availability: Usually ships in 1-2 weeks
Share
The Fiber Optic Adapter converts the electrical bulkhead of any Ikelite DS Substrobe into a fiber optic port. This adapter is a manual exposure (non-TTL) trigger only. The strobe's output must be adjusted using the manual power settings built into the strobe (varies by model).

Price (exc. VAT) €123.97

Price (inc. VAT) €150.00

Shipping cost from €14.00
Calculate shipping cost

Add to Cart

High Sensitivity Optical Slave Converter for Remote Triggering of DS Strobes

The High Sensitivity Optical Slave Converter is perfect for use in environments with high ambient light or large distances between your remote strobe and the primary flash.

This is a non-learning, sensor which requires the camera to be in manual flash mode. This Converter will not work with a preflash. The Optical Slave Converter supports manual exposure modes as set on the attached DS strobe. TTL exposure mode is not supported.

If your primary purpose is to trigger a strobe fiber optically by a compact digital camera's flash, we recommend the Fiber Optic Converter # 4401.1 or RC1 Olympus & Panasonic TTL Receiver # 4412 instead. 

High Speed Shooting

If you're shooting a DSLR or mirrorless camera with Nauticam fiber optic converter and want to shoot at high frame rates (4 FPS or faster), then this Converter is the right option for you. The included fiber optic port allows the attachment of Ikelite, SEA&SEA, Olympus, and certain Nauticam fiber optic cables.

Attachment and Use

The Converter simply attaches to the strobe's electrical bulkhead in place of a sync cord connector. The enlarged slave window provides approximately 90 degrees field of view for remote triggering. 

An optional 3-foot Extension Cord # 4102.03 may be added for more flexible positioning of the sensor window. This set-up is perfect for creative backlighting in wrecks, caves, and pool use. It can also be used above water for studio photography work.

An individual Converter is needed for each strobe. Use of multiple strobes requires one Converter per strobe. The Converter supports DS50, DS51, DS125, DS160 and DS161 strobes. 

This product replaces the Optical Slave Converter # 4403.

  • 1.1 diameter x 2.7 in (28 x 69 mm)
  • Weighs 1.6 oz (45 g)
  • Depth rating 300 ft (90 m)
  • Converter 4405
  • Silicone lubricant
IKELITE provides a limited warranty to the original purchaser against all defects in original workmanship and material under normal SCUBA use and service as outlined in the owner's manual for 2 years from the date of purchase, with the following exceptions:
  • This warranty does not cover commercial or rental use.
  • Should your equipment prove to be defective for any reason (other than those listed in the limitations section below) it will be repaired or replaced at IKELITE´s discretion, free of charge, excluding shipping and handling charges.
  • Repairs made under this warranty will not extend the warranty period
  • This warranty is non-transferable and applies to the original purchaser only.
  • All correspondence concerning this warranty must be accompanied by a copy of the original sales receipt.
  • Any flood or damage, for any reason, that is caused from flooding an O-ring sealed or water tight area will not be covered under warranty. All O-ring sealed products undergo extensive factory pressure testing before being shipped and delivered and are therefore guaranteed to be sealed and functioning when shipped from the factory.
  • IKELITE nor ADITECH will not be liable for any loss, damages, or expenses including incidental or consequential damages directly or indirectly arising from the sale or use of the product.
  • IKELITE accepts no liability for any loss of captured images or the inability to capture images even if it is due to the malfunctioning or leakage of the housing.
  • All paint finishing, cosmetic discoloration of surfaces, powder coating, or material stitching that is chipped, damaged, or unthreaded through customer use is not covered in the warranty.
  • IKELITE does not warranty any product for aesthetic finishes. Issues with surface finish that do not affect function of the product are not covered under warranty.
  • This warranty does not apply and may be rendered completely void in the event of accidental damage, abuse, overcharging of battery, flooding due to neglect, tampering, lack of care and maintenance, improper storage, or unauthorized service.
  • This warranty specifically excludes lenses, cords, connectors, O-rings, or other conditions resulting from misuse and negligence.
  • This warranty becomes void if the housing components are damaged by anything other than normal recreational diving use.
  • Modifications or repair by anyone other than an authorized IKELITE Dealer or ADITECH Service Department will void the warranty.
  • By purchasing this product you agree and understand that in no event will IKELITE, its distributors or retailers, be held liable for any personal injuries resulting from its operation, or any other damage whether direct, indirect, incidental or consequential, even if IKELITE or ADITECH is advised of such damages.

Do you have any doubts?