Overview & Features
RC1 Olympus & Panasonic TTL Receiver for DS Strobes
About this Product
Enjoy true Olympus or Panasonic LUMIX TTL strobe exposure via fiber optic connection with your compatible Ikelite DS strobe.
With the RC1 TTL Receiver and a compatible camera with RC flash mode,
actual exposure data is calibrated and communicated directly by the
camera. This is far more accurate and consistent than "slave TTL" modes
built into some underwater strobes which watch the camera's built-in
flash and react.
An individual RC1 TTL Receiver and compatible fiber optic cord is
needed for each strobe. Use of two strobes requires two receivers. See
strobe and cable compatibility information below.
This product attaches to an Ikelite DS strobe. It is not intended to
be attached to a housing and will provide no functionality if attached
to a housing bulkhead. This receiver is not compatible with non-Ikelite
strobes or non-digital Ikelite strobes.
RC Mode TTL Strobe Exposure
The Sensor makes DS Strobes compatible with the Olympus and Panasonic
LUMIX RC flash mode, providing automatic TTL exposure. For accurate
performance set the DS strobe to “TTL” and the camera’s flash mode to
“RC”. Using the camera’s flash exposure compensation controls to make
fine tuned adjustments to the strobe’s intensity.
Manual Strobe Exposure
The strobe's output may be adjusted using the manual power settings
built into the strobe (varies by model). Make sure the camera’s flash
mode is set to manual. Choose the minimum flash output necessary in the
camera to trigger the DS strobe. This will conserve the camera’s battery
power.
Technical Specifications
Camera & Housing Compatibility
Ikelite Housing Models:
- Olympus OM-D E-M10 Mark III in Ikelite Housing # 6950.13
- Olympus Stylus 1s in Ikelite Housing # 6139.51
- Olympus Tough TG-3, TG-4 in Ikelite Housing # 6233.03 / 6233.04 / 6233.05
- Olympus Tough TG-5 in Ikelite Housing # 6233.06 / 6233.07
Non-Ikelite Housing Models:
- Olympus OM-D E-M1 Mark II with FL-LM3 flash in Olympus or Nauticam Housing
- Olympus OM-D E-M5 Mark II with FL-LM3 flash in Olympus, Nauticam, or Isotta Housing
- Olympus OM-D E-M10 in Nauticam Housing
- Olympus OM-D E-M10 Mark II in Nauticam Housing
- Olympus OM-D E-M10 Mark III in Nauticam Housing
- Olympus Tough TG-3, TG-4 in Olympus, Nauticam, or Recsea Housing
- Olympus Tough TG-5 in Olympus, Nauticam, Isotta, or Recsea Housing
- Panasonic LUMIX GH3, GH4 with DMW-FL70 flash in any housing that supports use of the DMW-FL70 flash
- Panasonic LUMIX GH5, GH5s with DMW-FL70 flash in Nauticam or any housing that supports use of the DMW-FL70 flash
- Panasonic LUMIX GX8 with DMW-FL70 flash in Nauticam Housing
Consult with your housing manufacturer for information on what type
of fitting is provided at the housing end. The fiber optic ports
on Ikelite housings are made to the same standard as SEA&SEA and
Olympus brands.
Strobe Compatibility
- Ikelite DS50 above serial # 70000
- Ikelite D51
- Ikelite DS125 above serial # 5000
- Ikelite DS160, DS161
- Ikelite DS200 above serial # 7163
This product is not compatible with non-digital Ikelite strobes, SEA&SEA, INON, or other non-Ikelite strobes.
What´s Included
- RC1 Receiver
- Connector protector #0301.12
Warranty
IKELITE provides a limited warranty to
the original purchaser against all defects in original workmanship and
material under normal SCUBA use and service as outlined in the owner's
manual for
2 years from the date of purchase, with the following exceptions:
- This warranty does not cover commercial or rental use.
- Should your equipment prove to be
defective for any reason (other than those listed in the limitations
section below) it will be repaired or replaced at IKELITE´s discretion, free of charge, excluding shipping and
handling charges.
- Repairs made under this warranty will not extend the warranty period
- This warranty is non-transferable and applies to the original purchaser only.
- All correspondence concerning this warranty must be accompanied by a copy of the original sales receipt.
- Any flood or damage, for any reason,
that is caused from flooding an O-ring sealed or water tight area will
not be covered under warranty. All O-ring sealed products undergo
extensive factory pressure testing before being shipped and delivered
and are therefore guaranteed to be sealed and functioning when shipped
from the factory.
- IKELITE nor ADITECH will not be liable for any
loss, damages, or expenses including incidental or consequential damages
directly or indirectly arising from the sale or use of the product.
- IKELITE accepts no liability for any loss of captured images or the
inability to capture images even if it is due to the malfunctioning or
leakage of the housing.
- All paint finishing, cosmetic
discoloration of surfaces, powder coating, or material stitching that is
chipped, damaged, or unthreaded through customer use is not covered in
the warranty.
- IKELITE does not warranty any product
for aesthetic finishes. Issues with surface finish that do not affect
function of the product are not covered under warranty.
- This warranty does not apply and may
be rendered completely void in the event of accidental damage, abuse,
overcharging of battery, flooding due to neglect, tampering, lack of
care and maintenance, improper storage, or unauthorized service.
- This warranty specifically excludes lenses, cords, connectors, O-rings, or other conditions
resulting from misuse and negligence.
- This warranty becomes void if the housing components are damaged by anything other than normal recreational diving use.
- Modifications or repair by anyone other than an authorized IKELITE Dealer or ADITECH Service Department will void the warranty.
- By purchasing this product you agree
and understand that in no event will IKELITE, its distributors or
retailers, be held liable for any personal injuries resulting from its
operation, or any other damage whether direct, indirect, incidental or
consequential, even if IKELITE or ADITECH is advised of such damages.