Customer Support
+34 972 661 661
Price (inc. VAT)
€29.95
€62.00
Offer
-52%
Price (inc. VAT)
€69.95
€75.00
Offer
-7%
Price (inc. VAT)
€125.00
€195.00
Offer
-36%
Price (inc. VAT)
€368.00
€498.00
Offer
-26%
Price (inc. VAT)
€89.00
€249.00
Offer
-64%
Price (inc. VAT)
€59.00
€101.00
Offer
-42%
Price (inc. VAT)
€3,925.00
€5,375.00
Offer
-27%
Price (inc. VAT)
€49.00
€65.00
Offer
-25%
Price (inc. VAT)
€149.00
€199.00
Offer
-25%
Price (inc. VAT)
€25.00
€57.00
Offer
-56%

Ikelite 4403

Manufacturer: Ikelite
Availability: Usually ships in 1-2 weeks
Share
The Fiber Optic Adapter converts the electrical bulkhead of any Ikelite DS Substrobe into a fiber optic port. This adapter is a manual exposure (non-TTL) trigger only. The strobe's output must be adjusted using the manual power settings built into the strobe (varies by model).

Price (exc. VAT) €123.97

Price (inc. VAT) €150.00

Shipping cost from €14.00
Calculate shipping cost

Add to Cart

Optical Slave Converter for Fiber Optic / Remote Slave Triggering.

Trigger your Ikelite DS-series strobe off any camera or strobe flash. The Optical Slave Converter simply attaches to the strobe's electrical bulkhead in place of a sync cord connector. The enlarged slave window provides approximately 90 degrees field of view for remote triggering. Or thread on the included fiber optic port for the attachment of and triggering via a fiber optic cord.


Strobe Triggering

Trigger your Ikelite DS-series strobe off any camera or strobe flash. The Optical Slave Converter simply attaches to the strobe's electrical bulkhead in place of a sync cord connector. The enlarged slave window provides approximately 90 degrees field of view for remote triggering. Or thread on the included fiber optic port for the attachment of and triggering via a fiber optic cord.

The Optical Slave Converter can be extended using the optional 3-foot Extension Cord for creative backlighting in wrecks, caves, and pool studio set-ups. It can also be used above water for studio photography work.

The Optical Slave Converter supports manual exposure modes as set on the attached DS strobe. TTL exposure mode is not supported.

An individual Optical Slave Converter is needed for each strobe. Use of multiple strobes requires one Optical Slave Converter per strobe. The Optical Slave Converter supports DS50, DS51, DS125, DS160 and DS161 strobes.


Pre-flash auto detection

The Optical Slave Converter automatically configures itself for compatibility with both pre-flash and non pre-flash camera modes. No setting of small switches or confusion over number of pre-flashes. Simply turn on your strobe and take one picture to configure.


Fiber optic cord compatibility

  • Ikelite 4501 Fiber Optic Coiled Cord
  • INON Optical D Cable "Non-wireless type" L-Connector
  • Sea&Sea Fiber Optic Cable (L-type) Product No. 50107
  • Olympus UW Fiber Optic Cable PTCB-E02
  • Nauticam Optical Fiber Cable No. 26211 Nauticam to INON
  • Nauticam Optical Fiber Cable No. 26212 Nauticam to Sea&Sea
  • 1.1 diameter x 2.7 in (28 x 69 mm)
  • Weighs 1.6 oz (45 g)
  • Depth rating 300 ft (90 m)
  • Converter
  • Silicone lubricant
  • IKELITE provides a limited warranty to the original purchaser against all defects in original workmanship and material under normal SCUBA use and service as outlined in the owner's manual for 2 years from the date of purchase, with the following exceptions:
    • This warranty does not cover commercial or rental use.
    • Should your equipment prove to be defective for any reason (other than those listed in the limitations section below) it will be repaired or replaced at IKELITE´s discretion, free of charge, excluding shipping and handling charges.
    • Repairs made under this warranty will not extend the warranty period
    • This warranty is non-transferable and applies to the original purchaser only.
    • All correspondence concerning this warranty must be accompanied by a copy of the original sales receipt.
    • Any flood or damage, for any reason, that is caused from flooding an O-ring sealed or water tight area will not be covered under warranty. All O-ring sealed products undergo extensive factory pressure testing before being shipped and delivered and are therefore guaranteed to be sealed and functioning when shipped from the factory.
    • IKELITE nor ADITECH will not be liable for any loss, damages, or expenses including incidental or consequential damages directly or indirectly arising from the sale or use of the product.
    • IKELITE accepts no liability for any loss of captured images or the inability to capture images even if it is due to the malfunctioning or leakage of the housing.
    • All paint finishing, cosmetic discoloration of surfaces, powder coating, or material stitching that is chipped, damaged, or unthreaded through customer use is not covered in the warranty.
    • IKELITE does not warranty any product for aesthetic finishes. Issues with surface finish that do not affect function of the product are not covered under warranty.
    • This warranty does not apply and may be rendered completely void in the event of accidental damage, abuse, overcharging of battery, flooding due to neglect, tampering, lack of care and maintenance, improper storage, or unauthorized service.
    • This warranty specifically excludes lenses, cords, connectors, O-rings, or other conditions resulting from misuse and negligence.
    • This warranty becomes void if the housing components are damaged by anything other than normal recreational diving use.
    • Modifications or repair by anyone other than an authorized IKELITE Dealer or ADITECH Service Department will void the warranty.
    • By purchasing this product you agree and understand that in no event will IKELITE, its distributors or retailers, be held liable for any personal injuries resulting from its operation, or any other damage whether direct, indirect, incidental or consequential, even if IKELITE or ADITECH is advised of such damages.

    Do you have any doubts?